MVRC Rules 2022 (Grand Prix Cars)

Rules ver. 1.7

1. Reference Positions and Datums:

Longitudinal = X axis (+X = towards the rear)
Lateral/transverse = Y axis (+Y = towards the left when viewed from the front)
Vertical = Z axis (+Z = up)
FWCL = Front wheel centerline, RWCL = Rear wheel centerline

The reference plane is Z=0, which is coincident with the lowest surface of the allowed bodywork, excluding the floor plank. The wheelbase of the car is fixed at 3600mm with the FWCL at X=0 and the RWCL at X=3600mm.

2. Submission Requirements

2.1 An entry should be a single compressed archive file (ZIP etc) named using the format “<team>_<round>_<version>”. It must contain:

  • In a directory named “special_bc”:
    • (rule 7) One engine inlet surface, with a filename starting with “engineIn”
  • In a directory named “monitoring_surfaces”:
    • (rule 6) Each heat exchanger monitoring surface as a separate stl-file (front face of heat exchanger translated rearward along its normal by 30mm)
  • In a directory named “porous_media”:
    • (rule 6) Each (left and right hand sides) heat exchanger volume as a separate stl file
  • In a directory named “frt_wheels”:
    • MAND_Dummy_rims_frt_01
    • MAND_Wheels_frt_V01
  • In a directory named “rr_wheels”:
    • MAND_Dummy_rims_rr_V01
    • MAND_Wheels_rr_V01
  • In a directory named “high_res_surfaces” (rule 9.2).
  • In a directory named “vehicle_body”: All remaining bodywork.

2.2 These parts should be exported as separate stl files with 1 unit = 1m. Note: files must be saved with lower case suffix .stl (NOT .STL).

2.3 A full symmetric model must be submitted. Except where specified otherwise, any dimensions given apply to the entire car.

2.4 A plain text file must be included in the archive to specify the offset for the following parts compared to their position as supplied in the parts file, even if they have not been moved, stating the following:

  • Vehicle rake in deg (For the first races of 2022 it will be set at 0.0°)

2.5 Only the parts specified in rule 2.1 and the text file in rule 2.4 should be included. No other guide parts should be submitted. Please avoid including internal construction geometry. The combined size of the stl files (before compression) must be below 160MB for ASCII stl, or below 40MB for binary stl.

2.6 An unlimited number of entries may be submitted for a round at any time prior to the deadline, but only the most recent submission that was received prior to the deadline will be used. If no submission is made, the last submission from the previous round will be used automatically. Alternatively, contacting the MVRC organizers prior to the deadline, either by email or by submitting a text file through the normal entry submission method, it is possible to:

  • Nominate an entry from an earlier round of the same season to be re-used.
  • Extend the submission deadline by two days. This may only be done once per season.

3. Mandatory Supplied Parts

3.1 The following supplied parts, in their supplied position, and without modification must be used in the CFD model:

  • MAND_Exhaust_V04
  • MAND_Exhaust_Out_V04
  • MAND_Plank_V01
  • MAND_Mirrors_V02
  • MAND_Engine_MVRC_V01
  • MAND_Fuel_Cell_MVRC_V01
  • MAND_Gearbox_MVRC_V01
  • MAND_Helmet_MVRC_V04
  • MAND_Safetycell_MVRC_V07
  • MAND_Halo_2022_V04
  • MAND_Wheels_frt_V01
  • MAND_Wheels_rr_V01
  • MAND_Misc_Systems_V03
  • MAND_Dummy_rims_frt_01
  • MAND_Dummy_rims_rr_01
  • MAND_Susp_frt_V03
  • MAND_Susp_rr_V03

4. Supplied Volumes

  • RV_FRT_WING_VOL_V02
  • RV_RR_WING_V03
  • RV_RR_WING_PYLON_V02
  • RV_RR_WING_PROFILES_V01
  • RV_FLOOR_BODY_V03
  • RV_FLOOR_FENCE_V01
  • RV_FRT_WHL_DEFL_V03
  • RV_Vehiclebody_MVRC_V02
  • RV_Mirror_Strut_MVRC_V01

5. Supplied Reference Surfaces

  • 24_RS-FW-PROFILES_V01
  • 23_RS-FWEP-BODY_V01
  • 04_RS_FLOOR_REAR_V01
  • 02_RS-FLOOR-PLAN_V03
  • 31_RS-RW-RWEP_V01

6. Heat Exchangers

6.1 There must be one heat exchanger on each side of the car, meeting the following rules:

  • 6.1.1 Each heat exchanger is made up of a single planar shape extruded a distance of 60mm in a direction normal to it’s front face.
  • 6.1.2 The planar shapes may be rotated around the Y-axis only.
  • 6.1.3 Each shape must be at least 180,000mm2 in area.
  • 6.1.4 The heat exchanger extrusion must be located entirely inside the bodywork volume and must not intersect any bodywork or templates, but it must touch the bodywork along its edges to provide a realistic mounting to the body of the car.
  • 6.1.5 As specified in rule 2.1, the following parts must be included with the submission as separate stl files:
    • Each 60mm extrusion
    • A copy of each planar shape translated rearward along its normal by 30mm (i.e. the mid-surface of the extrusion)
Heat exchanger with monitoring surface located in center of volume

7. Power Unit Inlet

7.1 One engine inlet surface is required to be located above and behind the driver’s helmet on the car centreline, which:

  • 7.1.1 Must be one planar surface with an area of at least 15,000mm2.
  • 7.1.2 Must be at least 50mm high/wide at any point (measuring perpendicular to the boundary).
  • 7.1.3 Must be located within the bodywork volume at a point 1880mm rearward of the FWCL, and 700mm above the reference plane.
  • 7.1.4 The engine inlet inner templates are the volume(s) formed by an extrusion of each inlet surface rearward along its normal for a distance of 100mm. These templates must be entirely enclosed in bodywork and must not intersect any other parts or templates with exception of the engine intake plenum.
Inlet surface with next surface located 100m behind it

8. Power Unit Exhaust

  • 8.1 The exhaust is made of two mandatory parts, MAND_Exhaust_V01 and the surface MAND_Exhaust_Out_V01
  • 8.2 The volume inside of the tailpipe between exhaust out and the end of the exhaust pipe must remain unobstructed

9. Bodywork – General

9.1 All bodywork must be fully contained within the supplied legality volumes.

9.2 Parts inside of the volumes:

  • RV_FRT_WING_VOL_V01
  • RV_RR_WING_V02
  • RV_FLOOR_FENCE_V01
  • RV_FRT_WHL_DEFL_V02
  • RV_RR_WING_PROFILES_V01

must be included into the high_res folder.

9.3 No part of the bodywork may be less than 10mm thick. See appendix 1 for the exceptions to this rule.

9.4 The provided suspension parts may intersect the bodywork.

9.5 All body parts, including the supplied parts, must be capable of forming a single body, connected by parts meeting rule 9.3. i.e. there should be no floating parts.

9.6 When intersected with any X-plane, body work ahead of FWCL (X=0), not inside of RV_FRT_WING_VOL_V01, must produce only one continuous closed section.

Green sections are OK, red not so much

10. Front Wing

  • 10.1 Front Wing is everything inside of the volume RV_FRT_WING_VOL_V01
  • 10.2 Every cross section in the Y-plane inside of the volume RV_FW_PROFILES_V01 must produce no more than four closed sections.
  • 10.2 Every cross section in the Y-plane inside of the volume RV_FRT_WING_VOL_V01 must produce no more than four closed sections.
  • 10.3 The rearmost point of any such section must be visible when viewed from below.
  • 10.4 With exception of the rearmost closed section, the rearmost point of the remaining sections must not be visible when view from above.
  • 10.5 When viewed from below, the surface 24_RS-FW-PROFILES_V01 must not be visible.
  • 10.6 When view from the side, the surface 23_RS-FWEP-BODY_V01 must not be visible.

11. Rear Wing

  • 11.1 All body work inside of the volume RV_RR_WING_V02 is Rear Wing.
  • 11.2 Rear Wing bodywork inside of the volume RV_RW_PROFILES_V01 must:
    • 11.2.1 Contain exactly two sections in any Y-plane.
    • 11.2.2. The rearmost section must have a chord smaller than the first.
  • 11.3 The rear wing must be attached with at least three sections with one or two such sections inside of the volume RV_RR_WING_PYLON_V01 attaching to the gearbox.
  • 11.4 When view from the side, the surface 31_RS-RW-RWEP_V01 must be fully obscured.

12. Floor

  • 12.1 Body work inside of the volume RV_FLOOR_BODY_V01 is Floor.
  • 12.2 Floor must:
    • 12.2.1 Entirely obscure 02_RS-FLOOR-PLAN_V03 when viewed from below.
    • 12.2.2 Entirely obscure 04_RS_FLOOR_REAR_V01 when viewed from the side.
  • 12.3 When intersected with any X-plane, it must only produce only continuous closed sections with all parts of the section either visibly from above or below.
  • 12.4 When intersected with any Y-plane, it must only produce only continuous closed sections with all parts of the section either visibly from above or below.
  • 12.5 After these requirements are met, additional parts may be added to the volume inside of the volume RV_FLOOR_FENCE_V01:
    • 12.5.1 Up to four fences are permitted per side of the car.
    • 12.5.2 The fences must be a part extruded purely in Z-direction.
    • 12.5.3 The fences have to be a separate part.
    • 12.5.4 The fences must have a constant thickness of 10mm
  • 12.6 when viewed from below, the floor must be the lowest part of the car within the area defined by RS-Floor-plan.

13. Side Mirrors

  • 13.1 The mandatory part MAND_MIRRORS_V02 must be attached to the car by the mirror strut which when cut either in X-, Y- or Z-direction only produces one convex section.
  • 13.2 The mirror strut must lie inside of the volume RV_Mirror_Strut_MVRC_V01

14. Vehicle Rake

  • 14.1 With the car constructed in accordance with rules 1 to 12, above, the entire car, excluding wheels , may be be rotated a maximum of -1.2 degrees (nose down), with the center of rotation being located at X = 0mm, Z = 0mm.
  • 14.2 The competitor must nominate the number of degrees in the supplied text file.
  • 14.3 For the first races of MVRC 2022, the rake will be fixed at 0.0°.

Appendix 1: 10mm thickness

A1.1 For front and rear wing parts, each wing element should be at least 10mm thick at some part along its chord in any Y-section. Problems may be encountered at the CFD meshing stage if the thickness remains very low over a long distance at the rear of the chord.

A1.2 For thin bodywork elements (plates, strakes / fences), once the 10mm thickness requirement is met, a sharp trailing edge and rounded leading edge (roughly circular in shape) are permitted. The 10mm thickness should be maintained over approximately ⅔ of the length or more, and must be maintained in any load-bearing region.

A1.3 For any gurney flap / wickerbill, a triangular section is permitted if the base width is at least 10mm and the height is no more than 5 times the base width.

A1.4 Supplied mandatory bodywork may be below 10mm thick.

Appendix 2: airflow requirements for inlets and outlets

Engine Intake
  •  Velocity​ ​boundary​ ​condition​ ​will​ ​be​ ​applied​ ​such​ ​that​ the​ ​total​ ​intake​ ​flow​ ​rate​ ​is​ 0.3​ ​m3​/s​​ ​(whole​ ​car)
  • Total​ ​surface​ ​integral​ ​of​ ​pressure​ ​must​ ​be​ ​>=​ ​0​ ​Pa.m​2
Engine​​ Exhaust
  • Velocity​ ​boundary​ ​condition​ ​will​ ​be​ ​applied​ ​such​ ​that​ ​the​ ​total​ ​exhaust​ ​flow​ ​rate​ ​is​ 0.58​ m3/s​​ ​(whole​ ​car)
  • Total​ ​surface​ ​integral​ ​of​ ​pressure​ ​must​ ​be​ ​<=​ ​4.5​ ​Pa.m​2​​ ​(whole​ ​car)
Cooling
  • Heat​ ​exchanger​ ​will​ ​be​ ​given​ ​a​ ​certain​ ​porosity
  • Combined​ ​flow​ ​rate​ ​through​ ​heat​ ​exchangers​ ​must​ ​be​ ​>=​ ​3​ ​m3​/s​​ ​(whole​ ​car)

Violations of the engine intake and engine exhaust requirements will lead to a DNF. Not meeting cooling requirements leads to reduced engine power and to DNF below 50% of required value.

Appendix 3: Lap Time Prediction

Lap time prediction shall be performed by using Max Talyor’s new Lap Time Simulator. using the aerodynamic coefficients and characteristics of each car which are calculated by the CFD analysis program MantiumFlow.

Appendix 4: Realistic Designs

Structurally unrealistic designs will be judged to be illegal.